LPC18S10FBD144E NXP 32bit MCU

LPC18S10FBD144E Overview

The LPC18S10FBD144 is a Arm Cortex-M3 based microcontroller with securityfeatures for embedded applications. The Arm Cortex-M3 is a next generation core thatoffers system enhancements such as low power consumption, enhanced debug features,and a high level of support block integration.

The LPC18S10FBD144 operates at CPU frequencies of up to 180 MHz. The ArmCortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals. The ArmCortex-M3 CPU also includes an internal prefetch unit that supports speculativebranching.

The LPC18S10FBD144 includes 136 kB of on-chip SRAM, security features withAES engine, a quad SPI Flash Interface (SPIFI), a State Configurable Timer/PWM(SCTimer/PWM) subsystem, an externalmemory controller, and multiple digital and analog peripherals.

Features

Processor core
- Arm Cortex-M3 processor, running at frequencies of up to 180 MHz.
- Arm Cortex-M3 built-in Memory Protection Unit (MPU) supporting eight regions.
- Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC).
- Non-maskable Interrupt (NMI) input.
- JTAG and Serial Wire Debug, serial trace, eight breakpoints, and four watch points.
- Enhanced Trace Module (ETM) and Enhanced Trace Buffer (ETB) support.
- System tick timer.
On-chip memory
- 136 kB SRAM for code and data use.
- Multiple SRAM blocks with separate bus access.
- 64 kB ROM containing boot code and on-chip software drivers.
- 64 bit One-Time Programmable (OTP) memory for general-purpose use.
- Two banks (256 bit total) One-Time Programmable (OTP) memory for AES keystorage One bank can store an encrypted key for decoding the boot image.
AES engine for encryption and decryption of the boot image and data with DMAsupport and programmable via a ROM-based API.
Clock generation unit
- Crystal oscillator with an operating range of 1 MHz to 25 MHz.
- 12 MHz internal RC oscillator trimmed to 1.5 % accuracy over temperature andvoltage.
- Ultra-low power RTC crystal oscillator.
- Three PLLs allow CPU operation up to the maximum CPU rate without the need fora high-frequency crystal. The second PLL is dedicated to the High-speed USB, thethird PLL can be used as audio PLL.
- Clock output.
Configurable digital peripherals:
- State Configurable Timer (SCTimer/PWM) subsystem on AHB.
- Global Input Multiplexer Array (GIMA) allows to cross-connect multiple inputs andoutputs to event driven peripherals like timers, SCTimer/PWM, and ADC0/1.
Serial interfaces
- Quad SPI Flash Interface (SPIFI) with 1-, 2-, or 4-bit data at rates of up to52 MB per second.
- Four 550 UARTs with DMA support: one UART with full modem interface; oneUART with IrDA interface; three USARTs support UART synchronous mode and asmart card interface conforming to ISO7816 specification.
- Up to two C_CAN 2.0B controllers with one channel each. Use of C_CAN controllerexcludes operation of all other peripherals connected to the same bus bridge.
- Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMAsupport.
- One Fast-mode Plus I2C-bus interface with monitor mode and with open-drain I/Opins conforming to the full I2C-bus specification. Supports data rates of up to1 Mbit/s.
- One standard I²C-bus interface with monitor mode and standard I/O pins.
- Two I²S interfaces with DMA support, each with one input and one output.
Digital peripherals
- External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash,and SDRAM devices.
- Secure Digital Input Output (SD/MMC) card interface.
- Eight-channel General-Purpose DMA controller can access all memories on theAHB and all DMA-capable AHB slaves.
- Up to 83 General-Purpose Input/Output (GPIO) pins with configurablepull-up/pull-down resistors.
- GPIO registers are located on the AHB for fast access. GPIO ports have DMAsupport.
- Up to eight GPIO pins can be selected from all GPIO pins as edge and levelsensitive interrupt sources.
- Two GPIO group interrupt modules enable an interrupt based on a programmablepattern of input states of a group of GPIO pins.
- Four general-purpose timer/counters with capture and match capabilities.
- One motor control PWM for three-phase motor control.
- Repetitive Interrupt timer (RI timer).
- Windowed watchdog timer.
- Ultra-low power Real-Time Clock (RTC) on separate power domain with 256 bytesof battery powered backup registers.
- Alarm timer; can be battery powered.
Analog peripherals
- One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s.
- Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s.Up to eight input channels per ADC.
Unique ID for each device.
Power
- Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip internal voltage regulator forthe core supply and the RTC power domain.
- RTC power domain can be powered separately by a 3 V battery supply.
- Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deeppower-down.
- Processor wake-up from Sleep mode via wake-up interrupts from variousperipherals.
- Wake-up from Deep-sleep, Power-down, and Deep power-down modes viaexternal interrupts and interrupts generated by battery powered blocks in the RTCpower domain.
- Brownout detect with four separate thresholds for interrupt and forced reset.
- Power-On Reset (POR).
Available as LQFP144package.

Target Applications

Communication hubs
Automotive aftermarket
Power management
Consumer health devices
Embedded audio applications
Industrial control
Industrial automation
White goods

Applications

LPC18xx

Specifications

Core Processor ARM Cortex M3
Speed 180MHz
Operating Temperature -40℃ ~ 85℃ (TA)
Program Memory Type ROMless
RAM Size 136K x 8
Number of I/O 83
Peripherals Brown-out Detect/Reset, DMA, I2S, POR, PWM, WDT
Mounting Type Surface Mount
Oscillator Type Internal
Supplier Device Package 144-LQFP (20x20)
Package / Case 144-LQFP
Core Size 32-Bit
Connectivity CANbus, EBI/EMI, I2C, IrDA, Microwire, MMC/SD, SPI, SSI, SSP, UART/USART
Data Converters A/D 8x10b; D/A 1x10b
Voltage - Supply (Vcc/Vdd) 2.2V ~ 3.6V