LPC1830FBD144,551 NXP 32bit MCU

LPC1830FBD144,551 Overview

The LPC1830FBD144 is a high-performance, cost-effective Cortex-M3 microcontroller featuring 200 kB of SRAM, and advanced peripherals including Ethernet, High Speed USB 2.0 Host/OTG/Device and CAN 2.0B. Operating at speeds up to 180 MHz, the LPC1830 also features two new configurable peripherals: a SPI Flash Interface and a State Configurable Timer. All members of the series include a Wakeup Interrupt Controller allowing automatic wake from any priority interrupt as well as four reduced power modes: Sleep, Deep-Sleep, Power-Down, and Deep Power-Down.

Features

Arm Cortex-M3 processor, running at frequencies of up to 180 MHz
Arm Cortex-M3 built-in Memory Protection Unit (MPU) supporting eight regions
Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC)
Non-maskable Interrupt (NMI) input
JTAG and Serial Wire Debug
ETM and ETB support
System tick timer
200 kB SRAM for code and data use
32 kB ROM containing boot code and on-chip software drivers
Crystal oscillator with an operating range of 1 MHz to 25 MHz
12 MHz internal RC oscillator trimmed to 1 % accuracy
Ultra-low power RTC crystal oscillator
Clock output
Two PLLs allow CPU operation up to the maximum CPU rate
Quad SPI Flash Interface with four lanes and data rates of up to 40 MB/s
10/100T Ethernet MAC with RMII and MII interfaces and DMA support
One High-speed USB 2.0 Host/Device/OTG interface with DMA support
One High-speed USB 2.0 Host/Device interface with DMA support
Four 550 UARTs with DMA support: one UART with full modem interface
One UART with IrDA interface
One C_CAN 2.0B controller with one channel
Two SSP controllers with FIFO and multi-protocol support
One Fast-mode Plus I2C-bus interface with monitor mode
One standard I2C-bus interface with monitor mode and standard I/O pins
One I2S interface with DMA support and with one input and one output
External Memory Controller (EMC)
SD/MMC card interface
Eight-channel General-Purpose DMA (GPDMA) controller
Up to 83 General-Purpose Input/Output (GPIO) pins
GPIO registers are located on the AHB for fast access
State Configurable Timer (SCT) subsystem on AHB
Four general-purpose timer/counters with capture and match capabilities
One motor control PWM for three-phase motor control
One Quadrature Encoder Interface (QEI)
Repetitive Interrupt timer (RI timer)
Windowed watchdog timer
Ultra-low power Real-Time Clock (RTC) on separate power domain
Alarm timer; can be battery powered
One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s
Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s
Hardware-based AES security engine programmable through an on-chip API
Two 128-bit secure OTP memories for AES key storage and customer use
Unique ID for each device
Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip voltage regulator
RTC power domain can be powered separately by a 3 V battery supply
Four reduced power modes
Overdrive mode to increase CPU and bus clock frequency
Processor wake-up from Sleep mode via wake-up interrupts
Wake-up from Deep-sleep, Power-down, and Deep power-down modes
Brownout detect with four separate thresholds for interrupt and forced reset
Power-On Reset (POR)

Target Applications

Industrial
Consumer
White goods
RFID readers
e-Metering

Applications

LPC18xx

Specifications

Core Processor ARM Cortex M3
Speed 180MHz
Operating Temperature -40℃ ~ 85℃ (TA)
Program Memory Type ROMless
RAM Size 200K x 8
Number of I/O 83
Peripherals Brown-out Detect/Reset, DMA, I2S, POR, PWM, WDT
Mounting Type Surface Mount
Oscillator Type Internal
Supplier Device Package 144-LQFP (20x20)
Package / Case 144-LQFP
Core Size 32-Bit
Connectivity CANbus, EBI/EMI, Ethernet, I2C, IrDA, Microwire, SD, SPI, SSI, SSP, UART/USART, USB, USB OTG
Data Converters A/D 8x10b; D/A 1x10b
Voltage - Supply (Vcc/Vdd) 2.2V ~ 3.6V