MSP430FG6426IPZR Texas Instruments 16bit MCU

MSP430FG6426IPZR Overview

The TI MSP family of ultra-low-power microcontrollers consists of several devices featuring different sets of peripherals targeted for various applications. The architecture, combined with five low-power modes, is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the device to wake up from low-power modes to active mode in 3 μs (typical).

The MSP430FG6626 and MSP430FG6625 are microcontrollers with a high-performance 16-bit analog-to-digital converter (ADC), dual 12-bit digital-to-analog converters (DACs), dual operational amplifiers, a comparator, two universal serial communication interfaces (USCIs), USB 2.0, a hardware multiplier, DMA, four 16-bit timers, a real-time clock (RTC) module with alarm capabilities, an LCD driver, and up to 73 I/O pins.

The MSP430FG6426 and MSP430FG6425 are microcontrollers with a high-performance 16-bit ADC, dual 12-bit DACs, dual low-power operational amplifiers, a comparator, two USCIs, a 3.3-V LDO, a hardware multiplier, DMA, four 16-bit timers, an RTC module with alarm capabilities, an LCD driver, and up to 73 I/O pins.

Typical applications for these devices include analog and digital sensor systems, hand-held meters, such as medical diagnostic meters, measurement equipment, and hand-held industrial testers.

For complete module descriptions, see the MSP430F5xx and MSP430F6xx Family User’s Guide.

ECAD Model

Symbol

Footprint

Features

Low Supply Voltage Range:
3.6 V Down to 1.8 V
Ultra-Low Power Consumption
- Active Mode (AM):
  All System Clocks Active:
  250 μA/MHz at 8 MHz, 3.0 V, Flash Program Execution (Typical)
- Standby Mode (LPM3):
  Watchdog With Crystal, and Supply Supervisor Operational, Full RAM Retention, Fast Wakeup:
  3.2 μA at 2.2 V, 3.4 μA at 3.0 V (Typical)
- Shutdown RTC Mode (LPM3.5):
  Shutdown Mode, Active Real-Time Clock With Crystal:
  0.9 μA at 3.0 V (Typical)
- Shutdown Mode (LPM4.5):
  0.2 μA at 3.0 V (Typical)
Wake up From Standby Mode in 3 μs (Typical)
16-Bit RISC Architecture, Extended Memory, up to 20-MHz System Clock
Flexible Power-Management System
- Fully Integrated LDO With Programmable Regulated Core Supply Voltage
- Supply Voltage Supervision, Monitoring, and Brownout
Unified Clock System
- FLL Control Loop for Frequency Stabilization
- Low-Power Low-Frequency Internal Clock Source (VLO)
- Low-Frequency Trimmed Internal Reference Source (REFO)
- 32-kHz Crystals (XT1)
- High-Frequency Crystals up to 32 MHz (XT2)
Four 16-Bit Timers With 3, 5, or 7 Capture/Compare Registers
Two Universal Serial Communication Interfaces
- USCI_A0 and USCI_A1 Each Support
  - Enhanced UART With Automatic Baud-Rate Detection
  - IrDA Encoder and Decoder
  - Synchronous SPI
- USCI_B0 and USCI_B1 Each Support
  - I2C
  - Synchronous SPI
Full-Speed Universal Serial Bus (USB)
- Integrated USB-PHY
- Integrated 3.3-V and 1.8-V USB Power System
- Integrated USB-PLL
- Eight Input and Eight Output Endpoints
Continuous-Time Sigma-Delta 16-Bit Analog-to-Digital Converter (ADC) With Internal Reference With 10 External Analog Inputs, 6 Single-Ended and 4 Selectable as Differential or Single-Ended
Dual Low-Power Operational Amplifiers
Quad Low-Impedance Ground Switches
Dual 12-Bit Digital-to-Analog Converters (DACs) With Synchronization
Voltage Comparator
Integrated LCD Driver With Contrast Control for up to 160 Segments
Hardware Multiplier Supports 32-Bit Operations
Serial Onboard Programming, No External Programming Voltage Needed
Six-Channel Internal DMA
Real-Time Clock (RTC) Module With Supply Voltage Backup Switch
Device Comparison Summarizes Family Members