ATSAMDA1E14B-MBT Microchip 32bit MCU

ATSAMDA1E14B-MBT Overview

The SAM DA1 ARM® Cortex®-M0+ -based microcontrollers are operating at 48MHz (45DMIPS). The ATSAMDA1E14B provides 16KB Flash, 4kB SRAM and 512Byte RWW Flash. The connectivity peripheral set consists of 4 serial communication modules (SERCOM) that each can be configured to act as a USART, UART, SPI and I2C. Additional connectivity options are provided by the on-chip one channel Inter-IC sound interface (I2S) and the full-speed USB 2.0 embedded host and device.

Automotive Production DevicesThe ATSAMDA1 family is AEC-Q100 Grade 2 qualified. The standard device does not go through the automotive production flow, and there are two options for ordering devices with the automotive production flow.1) A customer specific part number will be assigned and designated with suffix to the base part number (i.e. ATSAMDA1E14B-MBTV02.) A customer specific PPAP is available on request.2) A generic suffix will be added to the base part number (i.e. ATSAMDA1E14B-MBTVA0.) A PPAP is unavailable for these devices.Please contact your local Microchip sales representative for additional information.

Supported by MPLAB X IDE and MPLAB Harmony.

Features

Processor

ARM Cortex-M0+ CPU running at up to 48MHz
Single-cycle hardware multiplier
Micro trace buffer

Memories

16KB in-system self-programmable Flash
0.5KB Read-While-Write (RWW) Flash section
4KB SRAM memory

System

Power-on reset (POR) and brown-out detection (BOD)
Internal and external clock options with 48MHdigital frequency locked loop (DFLL48M) and 48MHto 96MHz
fractional digital phase locked loop (FDPLL96M)
External interrupt controller (EIC)
16 external interrupts
One non-maskable interrupt
Two-pin serial wire debug (SWD) programming, test and debugging interface

Low power

Idle and standby sleep modes
SleepWalking peripherals

Peripherals

8-channel direct memory access controller (DMAC)
12-channel event system
Five 16-bit timer/counters (TC), configurable as either:
- One 16-bit TC with compare/capture channels
- One 8-bit TC with compare/capture channels
- One 32-bit TC with compare/capture channels, by using two TCs
Three 16-bit timer/counters for control (TCC), with extended functions:
- Up to four compare channels with optional complementary output
- Generation of synchronized pulse width modulation (PWM) pattern across port pins
- Deterministic fault protection, fast decay and configurable dead-time between complementary output
- Dithering for enhancing resolution with up to 5-bit and reduce quantization error
32-bit real time counter (RTC) with clock/calendar function
Watchdog timer (WDT)
CRC-32 generator
One full speed (12Mbps) universal serial bus (USB) 2.0 controller
- Device 2.0 and reduced-host low speed and full speed
- Flexible end-point configuration and management with dedicated DMA channels
- On-chip transceivers including pull-ups and serial resistors
- Crystal-less operation in device mode
Four serial communication interfaces (SERCOM), each configurable to operate as either:
- USART with full-duplex and single-wire half-duplex configuration
- I2C up to 3.4MHz
- SPI
- LIN slave
One two-channel inter-IC sound (I2S) interface
One 12-bit, 350ksps analog-to-digital converter (ADC) with up to 10 channels
- Differential and single-ended input
- 1/2x to 16x programmable gain stage
- Automatic offset and gain error compensation
- Oversampling and decimation in hardware to support 13-, 14-, 15- or 16-bit resolution

10-bit, 350ksps digital-to-analog converter (DAC)
Two analog comparators (AC) with window compare function
Peripheral Touch Controller (PTC)
- Up to 256-channel capacitive touch and proximity sensing

I/O